Four factors affecting the selection of shaker

<

There are many factors affecting the work of the shaker, including stroke, stroke, ore concentration, ore supply, water supply to the ore body, lateral slope of the bed, and the nature of the ore.

(1) Stroke and stroke strokes and strokes mainly affect the loose, stratified and selective transport of the ore particles on the bed. Stroke and punch are two important factors that are related to each other. When selecting fine materials, it is advisable to use small strokes and high strokes. When selecting coarse materials, the opposite is true. For coarse-grained materials (2.0 to 0.074 mm), the stroke can be adjusted between 15 and 27 mm, and the stroke can be adjusted between 250 and 280 times per minute. For slime, the stroke is 11-13 mm and the stroke is 350-360 beats/min. However, the most suitable stroke strokes are generally determined experimentally and are generally not adjusted during operation.

(2) Both the flushing water and the lateral slope of the bed surface mainly affect the lateral movement speed of the ore particles and the looseness of the foam layer. Increasing the slope can increase the speed of the water flow. Generally, when the fine material is treated, the slope should be smaller. When the coarse material is treated, the slope should be larger. The slope can be adjusted from 0° to 10°. 5度的小于小于0. 1。 For the different materials, the following values ​​can be used as a reference: less than 2 mm of the coarse-grained grades of 3. 5 ° ~ 4 °; less than 0. 5 mm of the material with 2. 5 ° ~ 3. 5 °; less than 0. 1 The fine material of millimeters is 2°~2.5°; for the slime (0.074 mm), about 20 is used. It should be noted that the choice of slope is well matched to the amount of water. The water flow in the area is evenly distributed, and the waves are not formed. The ore is not piled up. The selected zones are distinct, the bandwidth is thin, and the width of the bed-free zone is suitable.

The flushing water of the shaker consists of two parts: one part is the ore water fed along with the ore; the other part is the washing water directly fed to the bed. The lateral flow should be properly adjusted. On the one hand, the bed should be loose enough and the uppermost layer of light minerals can be washed away by the water. For this purpose, the water layer on the bed must cover the bed. On the other hand, however, it must be ensured that the densely colored ore particles can settle on the bed surface, so the lateral water velocity and the amount of water should not be too large.

The amount of flushing water is related to the lateral slope of the bed surface. Within a certain range, “large slope small water” and “small slope large water” can obtain similar sorting effects. When the slope is increased, the amount of flushing water can be reduced, but reducing the amount of flushing water and increasing the slope will narrow the mineral bands of different densities. When the quality of heavy minerals is required to be high, it is generally preferred to use a smaller slope to increase the flushing water. Flushing water and bed slope are factors that are often adjusted during operation. When the two are properly adjusted, there will be a uniform distribution of water flow in the stratified area on the bed surface, no wave, no heap of ore, and distinct zones. The bandwidth is thin and the width of the bed no-mine area is suitable.

(3) The ore concentration, the ore amount and the amount of dry ore delivered to the shaker to the ore body and the ore concentration determine the volume of the slurry. The ore concentration and the ore volume have a great influence on the selection of the shaker. The concentration of the ore is too large, the slurry is turned over, the fluidity is deteriorated, and many heavy minerals cannot be stratified; if the concentration is too thin, In addition to reducing the productivity of the shaker, the fine concentrate is also lost to the tailings. The appropriate slurry concentration should ensure sufficient fluidity of the slurry and stratified zoning of the ore particles on the bed. The normal ore concentration of the shaker is generally 15% to 30%.

The ore volume is also an important factor in the operation of the shaker. If the amount of ore is constant, the concentration of the ore is too low and the volume of the slurry is increased, which will result in a decrease in the recovery rate of the ore . If the amount of ore is given, the concentration of the ore is too large, which will also cause the recovery rate of the ore to decrease.

The amount of ore given depends on the size of the ore being processed.

(4) The density, grain size and shape of the ore-bearing minerals in the ore-bearing shaker have a great influence on the sorting index. When the density difference between heavy minerals and light minerals is greater than 1.5, it can be smoothly sorted on a shaker. Similar spherical granules and coarse particles are easily washed away by water. In the selection of the shaker, the material is generally classified, that is, hydraulic classification. Among the products obtained by hydraulic classification, the average particle size of the heavy mineral is much smaller than that of the light mineral, which is favorable for separation and stratification, and improves the separation. effect.

Link Pin is a device used for fastening/connecting objects or material together, mostly the Link Pin which QFAP supplied are applied in diggers, excavators, trucks, or railway equipments.

Most of our customers were from North America, Europe and Chinese domestic market.

 link pin

Annual Production Capability: 200,000pcs

Materials: carbon steel, stainless steel, alloys steel, steel tube, etc.

Surface treatment: painting, zinc plating, blackening, passivation, nickel plating, oiled, etc.

Heat treatment: according to customer`s requirement.

 

QFAP have specialized in producing high precision Agriculture Parts more than 10years, Because of the long term cooperation, we could supply our customers not only the products but also our recommendation on the designs to saving costs.

Link Pin

Link Pin,Linking Pin Model,Link Pin Kit,Link Pin Code

SHAOXING QIFENG AUTO PARTS CO., LTD. , https://www.sxqfap.com